Acidless Gold Recovery from BGA Solder Balls on Graphics Cards
A desktop graphics card is one of the densest concentrations of precious metal a household ever owns. At its centre sits the processor, soldered to a package substrate through a ball grid array: dozens of microscopic solder balls forming the mechanical and electrical bridge between the silicon die and the printed circuit board. It is tempting to picture that gold as sitting inside the solder. In most cards it does not. The solder balls are predominantly a tin-silver-copper alloy, occasionally capped with palladium or nickel in premium components, and their real value lies in the layers around them: gold-plated package interconnects, fine bonding wire, the die's own metallisation, and the thin electroless nickel immersion gold finish on the board itself.
Taken together, those layers put the gold content of a mid-range card in the order of a gram, with silver and palladium adding further value. That makes discarded graphics cards a prized urban-mining feed, and it makes using ALS2 for gold recovery from BGA solder balls on graphics processors a particularly tidy application for selective hydrometallurgy. Ikoi S.p.A. developed its acidless separation technology within a European Union Horizon 2020 project, with the explicit goal of lifting precious metals out of electronic waste and WEEE streams without the acid baths and cyanide circuits that dominate conventional refining. Australia, with heavy reliance on imported electronics and one of the world's largest gold markets, offers an obvious place to test the route.
Where the Metal Actually Sits in a Graphics Card
The ball grid array is the part everyone photographs. Each ball is a solder alloy that melts during reflow to connect the processor's pads to the substrate, and the balls have shrunk year on year as die sizes shrank, which makes the package harder to strip mechanically and harder to separate thermally. Composition varies widely: consumer cards use SAC-type alloys around 96.5% tin, roughly 3% silver and 0.5% copper, while high-reliability or legacy industrial boards can carry lead-bearing alloys, palladium-nickel caps or gold-bearing solders in specialised stacks.
Gold in a graphics card is a multi-layer problem rather than a single-target problem. It appears in the package as plating on the interconnects between processor and substrate, in the bonding wire that carries power and signal to the die, and in small amounts in the die attach itself. On the printed circuit board, the ENIG surface finish on pads and connectors adds a further gold layer, typically deposited over electroless nickel. Silver comes from the solder alloy and from tantalum capacitors, and palladium shows up in some multilayer ceramic capacitors and in plated components. Copper, tin, lead, aluminium, steel and plastic fill everything else.
The practical consequence is that a graphics card behaves like a layered feed rather than a homogenous ore. Any route that dissolves the whole board pulls hundreds of kilograms of base metal into solution along with the gold, which is exactly the problem acidless separation was designed to avoid.
What Acidless Separation Changes Chemically
Ikoi's ALS2 approach replaces the mineral acid systems used in conventional precious-metals refining with a non-acidic, selective reagent system that dissolves the target metals while leaving most base metals in the solid residue. Operating temperatures stay modest, reagents circulate in a closed loop, and the dissolved gold is recovered by controlled precipitation into a concentrated metallic product that a refinery can finish into doré bullion. No aqua regia, no cyanide circuit, no hydrochloric acid fumes, and no neutralisation sludge.
Selectivity is where the economics live. Because the reagent chemistry is tuned to precious metals rather than to bulk board dissolution, reagent consumption scales with the gold present instead of with the mass of the feed. Copper, tin and lead largely remain in the residue fraction, where they still have value to a mechanical recycler. The output is a small, high-grade product rather than a diluted pregnant leach solution, which cuts transport and handling volumes per tonne of gold recovered.
There is a permitting dividend as well. Acid-free chemistry simplifies hazardous-substance classification, fume control requirements and hazardous waste manifests for the operator. Australian sites that already hold waste processing licences under state regulators such as the NSW EPA or the Environment Protection Authority Victoria find that a chemistry with no strong acids and no cyanide attracts fewer compliance conditions than a greenfield acid plant, and it slots more easily into an existing facility footprint.
Turning a Card Stream into Usable Feedstock in Australia
Australian e-waste volumes are large and poorly captured. University of Queensland research has put national generation at roughly 5.8 million tonnes a year, or more than 20 kilograms per person, with a minority formally recycled. Household behaviour drives most of the loss: old cards sit for years in the "drawer of shame" awaiting a future project, e-waste still ends up in general waste in some council areas, and regional households in parts of NSW and Queensland are more likely to leave obsolete electronics in sheds or backyards than to drive them to a drop-off.
The route to a chemical recovery line starts with disciplined pre-processing. Cards must be stripped of fans, heatsinks and backplates, which are mixed aluminium, copper and plastic; often the card is shredded so the package, board and connectors are separated by density and magnetic response. That mechanical stage is where most existing Australian e-waste recyclers already operate, and it is where a downstream precious-metals step can be added without rebuilding the front end.
Chain of custody matters at this point. Buyers of Australian e-waste increasingly expect e-Stewards or equivalent R2 certification, documented mass balances and refinery-grade assay records. National policy frameworks through the National Waste Policy and state strategies push recovery targets and restrict e-waste in landfill, while Australia's obligations under the Basel Convention and used waste export rules limit shipping e-waste offshore for treatment in jurisdictions with weaker controls. Keeping a high-value, low-weight card stream inside Australia for chemical recovery satisfies all of those expectations at once.
The comparison below sets the ALS2 route against the two alternatives most Australian recyclers currently consider for graphics-card streams.
| Parameter | ALS2 acidless separation | Aqua regia or cyanide leaching | Shredding and manual sorting |
|---|---|---|---|
| Reagent system | Non-acidic selective dissolution, closed-loop reagents | Strong mineral acids, cyanide or bromide circuits | None, physical separation only |
| Typical operating temperature | Near ambient | Elevated and exothermic, with fume control | Ambient |
| Gold selectivity | Targets gold-bearing layers, base metals largely retained | Bulk dissolution of the entire board | Low, dependent on labour and visible parts |
| Secondary waste | Minimal, no neutralisation sludge | Acid sludge and neutralisation salts | Mixed plastic and metal fines to landfill |
| Product form | Concentrated precious-metal product for refining | Crude precipitate needing further refining | Mixed metal scrap at commodity prices |
| Footprint | Compact, container-ready cell | Tank farm, bunding, gas handling | Low capital, high labour |
| Permitting burden | Simplified hazardous-substance classification | Heavy hazardous-substance and air controls | Mostly general waste handling |
| Suitability for card streams | Strong, high value per kilogram | Workable but reagent-hungry | Weak, gold lost to fines |
Where the Revenue Sits for a Compact Recovery Plant
The commercial case rests on a simple comparison: e-waste is ore-grade metal at urban scale. A tonne of graphics-card boards can carry tens of grams of gold, while a good hard-rock gold operation in Western Australia might see only a few grams per tonne of ore. The gold price in Australian dollars, sitting on ASX-listed products and supported by bullion demand through channels such as the Perth Mint, keeps the arithmetic attractive for a well-run facility.
Gold has also become one of Australia's largest export earners by value, which means recovering it from domestic waste streams has a direct trade balance argument as well as an environmental one. For a recycler, the practical upside is a new revenue line at the end of an existing mechanical process: shredded card and board fraction in one direction, a refined precious-metal product sold to a refinery in the other. The ALS2 footprint suits that arrangement, since a containerised cell can be installed on hardstanding at an existing transfer station rather than requiring a new industrial estate and a full acid infrastructure build.
The risks are ordinary and manageable. Feed composition swings with the market, so cards from top-of-the-range accelerators carry more precious metal per kilogram than entry-level models. Assaying and sampling need to be rigorous, and the recovery product has to meet a refinery's specification. Chemistry selectivity addresses the largest operating cost driver, which is reagent consumption per tonne treated, and it does so without exposing the site to the volatile acid market.
Bring the ALS2 Route to an Australian Feedstock Stream
Ikoi's ALS2 platform was built for exactly this kind of application: compact precious-metals recovery from electronic waste and WEEE, developed with European Union Horizon 2020 support and now available for industrial demonstration. Graphics-card and BGA-derived feed is a strong first campaign because the precious-metal concentration is high, the material is light to transport and the pre-processing requirements are already understood by most licensed recyclers.
Australian operators can engage on several tracks, including a technical dossier review, feed characterisation on a locally collected card stream, and discussion of supplying a demonstration plant for an existing facility in Sydney, Melbourne, Adelaide or a regional hub. Ikoi also works with partners on licensing and revenue-sharing structures for modular plants sited beside existing mechanical recycling lines.
To move forward, contact Ikoi S.p.A. for the ALS2 technical dossier, the feed characterisation protocol and a demonstration campaign plan built around a local graphics-card and BGA-derived stream.