Shear Control For Effective ALS2 Coating Separation

Recovering precious metals from electronic waste depends on releasing valuable coatings from the materials beneath them. Gold, silver, palladium and copper may be present in very thin layers, yet they are bonded to nickel, copper alloys, plastics, ceramics, solder residues and other components. The separation step must therefore be powerful enough to liberate the coating without turning the entire feed into an unmanageable mixture of fines.

In an ALS2 process, shear is a key mechanical action. It describes the tangential force that makes one surface or particle move across another. This differs from simple impact, compression or abrasion, although all may occur together inside a compact recovery plant. The useful operating point is the point where coating adhesion and material strength are overcome with controlled energy input.

There is no universal shear-force number for every electronic waste stream. A plated connector, a printed circuit board, a mobile phone fraction and a mixed WEEE feed each respond differently. Effective settings depend on coating thickness, substrate type, particle size, moisture, contamination and the equipment geometry used in the ALS2 line.

This matters particularly in Australia, where a recycler may process a consistent industrial feed in Melbourne one day and a mixed collection from a regional transfer station near Newcastle, Bendigo or Townsville the next. Long transport distances from Western Australia or the Northern Territory can also encourage stockpiling, making stable and flexible processing conditions commercially important.

Why Coating Liberation Depends On Shear

A coating remains attached when the bond between layers is stronger than the mechanical stress applied to it. Shear acts parallel to the interface, encouraging a plated layer to slide, buckle, crack or peel away from its substrate. The required force depends on whether the bond is metallic, adhesive, oxidised, soldered or partly weakened by previous use.

The critical point is selective liberation. If shear is too low, valuable coating remains attached and reports to the wrong fraction. If it is too high, the substrate can fracture, polymer can smear across particles, and fine dust can increase. A suitable ALS2 operating window creates enough relative motion to separate the valuable layer while preserving distinct material fractions for downstream recovery.

This principle also explains why rotational speed alone is not a reliable specification. The actual stress depends on speed, rotor or tool diameter, clearance, feed size, residence time, filling level and the frictional behaviour of the material. Two machines running at the same revolutions per minute can apply very different shear conditions.

Feed Characteristics Set The Starting Point

Feed preparation is the first control over shear demand. Large housings, cables, boards and connector assemblies behave differently from a prepared fraction of small, liberated particles. Pre-sorting can remove batteries, bulky steel, excessive plastics and hazardous components before the coating-separation stage, reducing unnecessary energy use and protecting equipment.

Particle size distribution is especially important. Large pieces may shield plated surfaces from contact, while an excessive amount of fines can cushion the mechanical action and carry coatings away in dust. A controlled size range gives the equipment a more predictable contact pattern and makes residence-time adjustments easier.

Surface condition also changes the required force. Weathered material may have corrosion products and weakened interfaces, reducing the energy needed for release. Clean industrial scrap may have a more intact bond and require stronger action. Moisture can increase cohesion between particles, while oils and dirt may alter friction and make separation less consistent.

Australian collection systems create substantial variation. Material from a metropolitan transfer station may contain household electronics, while a mining or telecommunications stream can contain higher-value, more uniform components. The term “e-waste” may cover both, even though their mechanical treatment requirements are far apart.

Designing The Useful Shear Window

The effective shear range sits between incomplete liberation and excessive breakage. In practical terms, operators look for enough tangential stress to expose the coating, combined with suitable contact time and repeated particle movement. The process should produce a valuable fraction with a high concentration of precious-metal-bearing material and a substrate fraction with minimal residual coating.

Engineering teams can describe the operating condition through shear stress, strain rate and specific energy. Shear stress is related to force divided by contact area, while strain rate describes how quickly neighbouring layers move relative to each other. Specific energy indicates how much energy is used per kilogram of feed. These measures are more useful for comparing trials than a speed setting by itself.

Clearance and fill level have a direct influence on the result. A narrow working gap may increase contact intensity, but it can also raise heat, wear and the risk of compaction. A heavily loaded chamber may reduce relative movement and create dead zones. A lightly loaded chamber may deliver intense contact to individual particles but reduce overall throughput.

The ALS2 approach should therefore be tuned as a process window rather than a single fixed setting. Pilot testing can establish the lowest energy condition that reaches the target liberation level, then define acceptable limits for fines, dust, noise, temperature and equipment wear.

Measuring Whether Separation Is Effective

Visual inspection is useful but insufficient. A clean-looking particle can still retain a thin gold or silver layer, while a dark flake may contain valuable metal hidden beneath oxidation or contamination. Representative sampling before and after treatment is needed to calculate recovery, grade and residual coating content.

Useful indicators include precious-metal concentration in the recovered fraction, metal losses in the reject stream, particle-size distribution, dust generation and the percentage of substrate pieces still carrying visible plating. Microscopy, image analysis and laboratory assays can reveal whether the coating has peeled away cleanly or has been smeared across other particles.

The balance between liberation and degradation is central. Excessive shear may create particles that are too small for efficient screening or separation. It may also mix polymers and metals so closely that later sorting becomes less effective. A strong result is therefore measured by overall recovery quality, not simply by the amount of mechanical energy applied.

Operators should record feed composition and machine conditions with every trial. A change from server boards to mixed consumer electronics can alter the outcome even when the nominal throughput and speed remain unchanged. Consistent records make it possible to distinguish a true equipment issue from a change in feed behaviour.

Avoiding Over-Shearing And Unstable Operation

Over-shearing can be identified through several warning signs: rising motor load, increased temperature, excessive fines, visible smearing, blocked screens and declining purity in separated fractions. It may also accelerate wear on liners, shafts, seals and other contact surfaces. These symptoms indicate that the process is spending energy on damage rather than useful liberation.

Dust control deserves particular attention. Fine metallic and polymeric particles can create occupational and housekeeping risks, especially when dry feed is handled at high intensity. Enclosed equipment, extraction, filtration and suitable monitoring should be designed alongside the mechanical process rather than added after commissioning.

Feed interruptions and surges can also shift the shear environment. A sudden empty chamber may increase local intensity, while an overloaded chamber can reduce movement and raise torque. Stable metering, appropriate screening and interlocks help maintain consistent conditions and protect the plant.

For Australian operators, practical maintenance planning must account for distance and availability of parts. A facility outside Perth, Adelaide or regional Queensland may not be able to wait several weeks for a specialised component. Monitoring wear and keeping critical spares on site can protect production schedules and reduce unplanned transport costs.

Scaling ALS2 Separation For Australian Recycling

A compact precious-metals recovery plant must connect mechanical separation with the wider recycling chain. Incoming material may arrive from council programs, appliance retailers, repair businesses, data-centre decommissioning or scrap-metal aggregators. Each source has different levels of contamination, documentation and supply regularity.

Local terminology and market expectations matter as well. Australians commonly refer to a recycling facility as the “tip” or transfer station, while industry documents may use WEEE, e-waste or end-of-life electrical equipment. A plant specification should make clear which feed types are accepted, which items require pre-treatment and how recovered fractions are valued.

The commercial case depends on yield, purity, labour, power, maintenance and transport. Removing acids from the separation route can reduce chemical handling requirements, but mechanical energy and dust-management costs still need to be measured honestly. When communicating the value of recovered material, plain language helps, whether the audience is a plant manager comparing yields or a visitor reading about one-cent slots; the technical message should remain clear and evidence-based.

Regional scale can favour modular equipment. A smaller plant located closer to collection points may reduce freight and storage costs, while a larger metropolitan facility may benefit from more uniform feed and established laboratory services. ALS2 performance should be evaluated against the actual Australian supply network rather than an idealised feedstock.

Comparing Shear Conditions In Practice

The following framework shows how operating conditions can affect coating liberation. It is a guide for trials, not a substitute for measurements on the specific ALS2 equipment and feed.

Operating condition Likely separation result Typical warning signs Process response
Too little shear Coatings remain attached to boards, connectors or substrates Low valuable-metal grade, visible plating on rejects Increase controlled contact, improve feed preparation or extend residence time
Balanced shear window Coatings are liberated with limited substrate damage Stable torque, controlled fines, clear fraction differences Maintain settings and verify with assays
Excessive shear Coatings and substrates break down together High dust, smearing, heat, wear and poor fraction purity Reduce intensity, adjust clearance or loading, improve extraction
Unstable shear Results vary between batches Torque fluctuations, surges and inconsistent particle size Improve metering, screening, moisture control and monitoring

A reliable commissioning program should test several feed compositions and operating points. Samples should be taken from the feed, liberated fraction, substrate fraction and dust-control system. Results can then be compared using mass balance, precious-metal assays and particle-size data rather than relying on appearance alone.

The best setting is usually the lowest practical shear intensity that achieves the required liberation and throughput. This reduces wear and energy demand while preserving the value of cleanly separated fractions. It also gives operators more room to manage seasonal changes, variable collection streams and occasional contamination.

ALS2Project presents an acidless route for recovering precious metals from electronic waste and WEEE streams. To explore how controlled mechanical separation can support safer, cleaner recycling, review the project’s technology and sustainability information, then assess the approach against your own feedstock, plant scale and recovery targets.