Temperature in ALS2 Gold Stripping from Nickel Underlayers

Electronic waste from discarded phones, computers, networking gear and industrial controls often contains connectors with a very thin gold layer over a nickel underlayer. That layer is valuable, yet removing it cleanly is difficult because nickel can enter the same metal stream. ALS2Project presents Ikoi S.p.A.’s acidless separation technology as a safer option for compact precious-metals recovery plants, where yield, waste control and simple operation must coexist.

Temperature is one variable that can make or break an ALS2 stripping step. It changes reaction rate, mass transfer, viscosity and the behaviour of the process medium around gold-bearing nickel surfaces. It can influence both gold recovery and nickel carry-over. The practical question is not whether hotter is better, but which temperature gives the best balance of recovery, selectivity, reagent stability, throughput and energy demand.

Temperature cannot be separated from the rest of the flowsheet. Bath composition, agitation, feed preparation, residence time and any electrical drive interact with heat. A laboratory set point can fail in a pumped skid with different surface-area-to-volume ratios. ALS2 development should therefore qualify a temperature operating envelope using metallurgical balances, not a single nominal figure copied without context.

For Australian operators, that envelope must fit a dispersed e-waste network. Sydney and Melbourne generate substantial mixed WEEE from households, refurbishment businesses and commercial IT, while depots in regional Queensland or Western Australia can sit hundreds of kilometres from a metropolitan processing hub. Hot conditions around Brisbane and Perth, cooler winters in Melbourne and Adelaide, and variable industrial energy prices make thermal design commercially relevant.

Why Temperature Changes ALS2 Performance

In an ALS2 stripping stage, the process medium contacts gold supported on nickel, and the target is to transfer gold into a separately recoverable stream while controlling nickel dissolution. Temperature affects several steps at once: chemical reaction, transport through boundary layers, wetting of the component and, where applicable, electrode behaviour. This is why the best process condition is a controlled range rather than a simple “hotter” rule.

Temperature condition Likely process effect Selectivity and stability Plant implication
Cooler setting Higher viscosity and slower diffusion can limit gold transfer. May slow nickel attack, but can also leave gold in solid residues. Longer cycles or lower throughput.
Validated operating range Balanced reaction rate and mass transfer under the selected ALS2 chemistry. Best opportunity for repeatable gold recovery and low nickel carry-over. Tight control of temperature, agitation and feed.
Warmer setting Faster reaction and easier flow may lift the initial stripping rate. Greater risk of nickel co-dissolution, reagent degradation or changed passivation. Use only where balances confirm a net benefit.

Raising temperature usually speeds the chemical reaction more strongly than it improves diffusion, so the gain can flatten once mass transfer becomes limiting. Lower viscosity and better wetting may still raise the rate at the component surface. In a batch bath, this can shorten a cycle; in continuous equipment, it changes the balance between reaction, residence time and heat removal.

Selectivity can move in the opposite direction. A warmer medium may accelerate the undesired reaction of nickel or destabilise a complexant, while a cooler medium can preserve the nickel underlayer but leave gold in residues. The preferred band must therefore be established for each feed class and confirmed when the stripped solids move into downstream metal recovery.

Preparing Feed for Reliable Stripping

A temperature trial is only meaningful if the feed resembles the material an Australian plant will process. Used connectors may arrive with solder, plastics, cleaning residues, copper contacts and varied plating systems. Selective dismantling and a light cleaning step can reduce variability, but aggressive pre-treatment must not remove or alter the gold–nickel layer being studied.

Particle size, component geometry and solids concentration then influence heat and mass transfer. A tightly packed batch may warm differently from a well-agitated slurry, even at the same measured temperature. The operating recipe should define how components are presented to the ALS2 medium, because temperature cannot correct for poor wetting or inaccessible surfaces.

Representative sampling is equally important. A handful of gold-bearing contacts from one device may not reflect connector types collected through council e-waste drop-offs or commercial IT decommissioning. Trial batches should span expected plating thicknesses, nickel finishes, contamination levels and device origins, with feed composition recorded alongside every temperature result.

Gold Recovery and Nickel Selectivity

Gold recovery percentage is only one part of the result. Each balance should also report nickel carried into the gold-bearing solution or product, gold left in solid residues, reagent consumption and the mass of additional solids generated. Those figures reveal whether a higher temperature is creating value or merely transferring more material into the wrong stream.

Temperature changes competing reaction rates, not just the desired one. If nickel dissolution accelerates faster than gold transfer, recovered gold can become harder to refine. Complexant stability, precipitation, surface passivation and emulsion behaviour may also vary with heat where those features are relevant to the ALS2 medium. Any such change should be checked through chemical analysis rather than inferred from appearance.

A practical operating window is therefore defined by several limits at once. The lower limit must deliver adequate recovery within the available cycle time; the upper limit must protect selectivity and process stability. Feed variation, storage delays and incoming water quality can shift those limits, making a small operating margin valuable even after a successful pilot campaign.

Process Control for Compact Plants

A compact ALS2 skid needs more than a heater and a thermostat. Temperature should be measured at the working volume, not only at a heat-exchanger outlet, while circulation, agitation and residence time remain stable. A programmable controller, redundant sensing where justified, and an independent over-temperature shutdown help prevent an excursion from changing the metal balance.

Instrumentation and laboratory support can be scoped with experienced suppliers, including Cavendish Instruments, for the measurement and control requirements of qualification trials. The same discipline applies to tanks and pipework: insulate lines, prevent hot spots, contain losses and provide a controlled way to cool or warm a batch before discharge.

Australian climate affects the balance between heating and cooling. A module in Brisbane or Perth may spend more energy removing reaction heat, while a Melbourne or Adelaide installation may need reliable preheating during cold starts. Heat recovery from warm effluent can reduce demand, but it should not force the operating temperature away from the qualified ALS2 range.

Australian Market Fit

Regulation and collection are organised differently across Australian states and territories. Councils run e-waste drop-offs, while producers, retailers, recyclers and approved contractors use take-back arrangements under changing local rules. Training should reflect the plain language used at depots and workshops—“e-waste”, “strip bath” and “gold-bearing contacts”—while retaining formal references to WEEE, PCB and nickel underlayer.

That fragmented market rewards compact, modular recovery equipment. Installing a small ALS2 line near a high-volume collection point can shorten freight of concentrated electronic scrap and lower handling of mixed WEEE. For a depot in regional Queensland or Western Australia, the same unit may serve several surrounding areas, provided feedstock contracts and safe transport of recovered metal are settled before scale-up.

Sustainability must be measured locally. Avoiding acid-based refining can reduce worker exposure and hazardous effluent, yet temperature control also consumes energy and affects reagent use. The European Union’s Horizon 2020 research and innovation programme gives ALS2Project a structured development foundation; Australian partners should add local life-cycle evidence, including transport distance, electricity demand and the primary production that recovered metal actually displaces.

Qualification Pathway for Australian Operators

The next stage should be a controlled temperature campaign using representative Australian WEEE. Test low, nominal and elevated conditions while holding composition, agitation, current or potential where applicable, and residence time constant. Analyse gold recovery, nickel carry-over, reagent consumption and energy per batch, then use replicate runs to expose variability that a single laboratory result can hide.

Scale-up should follow in defined increments: laboratory vessels, a pilot reactor and then a skid with the intended mixing and heat-transfer geometry. Acceptance criteria should include stable control around the chosen set point, predictable gold yield, acceptable nickel purity, safe shutdown and operator competence. Mass-balance data from each stage provides the evidence needed for investment and insurance discussions.

Australian operators should now secure representative WEEE, form a team spanning metallurgy, chemistry and process control, and commission an ALS2 temperature trial before committing to commercial plant scale.