The influence of copper ion concentration on ALS2 selectivity for gold
Precious-metal recovery from electronic waste and WEEE depends as much on separation quality as on the quantity of gold present. Connectors, contact fingers and integrated circuits can carry recoverable gold, while copper enters the same stream through wiring, motors, relays and printed circuit boards. ALS2Project’s acidless separation technology is intended to recover precious metals without the acid-heavy refining route used in many conventional flows.
For ALS2, dissolved copper ions are an active process variable rather than background contamination. Their concentration can alter how much gold is recovered, how much copper accompanies it, and how much separation reagent remains available. The practical question for plant designers is therefore where selectivity begins to weaken, which feed conditions cause that shift, and how copper can be controlled before a compact recovery unit receives WEEE-derived feed.
Copper changes the selectivity balance
An acidless route is not a copper-inert route. Copper can participate in the same complexation, adsorption or separation reactions used to distinguish gold from other metals. As free Cu²⁺ activity increases, more reactive capacity may be directed toward copper, reducing the proportion of ALS2 reagent available for gold. The result can be lower gold selectivity even when the absolute amount of recovered gold changes little.
Low copper concentrations generally provide more room for a gold-directed response. At higher concentrations, copper co-recovery and reagent consumption become increasingly important, while sudden copper-rich batches can disrupt an otherwise stable separation. No universal concentration threshold applies because the response also depends on pH, ligands, temperature, residence time and the physical form of the feed. The operating pattern can be summarised as follows:
| Dissolved copper condition | Effect on ALS2 gold selectivity | Practical response |
|---|---|---|
| Low, stable background copper | Gold-directed separation is generally easier to maintain, with limited copper co-recovery. | Establish a baseline using matched feed assays. |
| Moderate, gradually rising copper | Gold recovery may remain useful, but Au-to-Cu discrimination narrows as reactive capacity is shared. | Control reagent dosing and track copper entering the gold-bearing stream. |
| High copper or batch spikes | Co-recovery, reagent demand and copper-bearing residues become more likely. | Blend and equalise the feed before separation. |
| Copper-rich fines or solids | Apparent selectivity may worsen through physical entrainment even when dissolved copper is moderate. | Filter, wash and account for fines in the mass balance. |
Recovery and selectivity should not be treated as interchangeable measurements. A process can maintain strong gold recovery while producing a gold fraction that contains too much copper. Likewise, a high assay in the final product does not prove that the upstream separation was efficient. Copper control must be assessed through recovery, product composition, reagent consumption and residue generation together.
Concentration effects depend on the whole solution
The most informative copper measurement is the concentration of dissolved, chemically available Cu²⁺, rather than the total copper content of the incoming WEEE. Copper locked in insulation, enamel or plated components may dissolve slowly and have little immediate effect on ALS2. Conversely, fine copper-rich particles generated during shredding can dissolve rapidly and create a processing spike.
Solution chemistry also changes how copper behaves. pH affects precipitation and ligand availability, while chloride, ammonia, organic complexants and other constituents can alter copper speciation. Ionic strength can influence phase separation and reaction kinetics. Increasing one copper concentration in a simplified laboratory solution may therefore produce a different response from adding copper to a real electronic-waste leachate.
Physical separation adds another layer. Suspended solids can adsorb dissolved gold, carry copper into the recovered fraction or settle prematurely. Temperature, agitation and filtration determine whether the measured solution chemistry translates into a clean solid–liquid separation. ALS2 selectivity must therefore be evaluated under conditions that reproduce both the aqueous matrix and the solids profile of the intended feed.
Testing copper effects with useful evidence
A credible copper-response programme uses a controlled series rather than comparing unrelated batches. Synthetic solutions establish how gold and copper respond as copper is spiked, while matched WEEE leachates test whether real matrix constituents change that relationship. Gold concentration, pH, temperature, residence time and ALS2 dosage should remain constant so that copper is the principal variable.
Sampling needs to distinguish several copper populations. Total copper can be measured in the solid feed by XRF, while ICP-OES or ICP-MS can quantify dissolved copper and other metals after appropriate preparation. Filtration and solids digestion reveal how much copper is dissolved, particulate or retained in residues. Samples should also be taken across the batch because an average concentration can conceal the short spike most likely to damage selectivity.
Useful performance measures include gold recovery, copper co-recovery, Au-to-Cu separation, product grade and ALS2 consumption per unit of feed. Material balances should account for gold and copper in every outlet, including filter cake and tailings. A rise in gold recovery caused by extra reagent is economically different from genuine selectivity improvement, and it may disappear when the reagent penalty is included.
Translating selectivity into plant controls
Copper control begins before the ALS2 separation stage. Incoming WEEE-derived solutions can be sampled, analysed and blended to reduce batch variation. A compact plant can use holding capacity or controlled dosing to manage copper spikes, especially when loads arrive from mixed household, commercial and industrial collection streams. Feed records should include source, particle size and any known motor or cable content.
During separation, reagent dosage should respond to measured copper rather than a fixed assumption. Operators also need visibility into pH, temperature, solids carry-over and the composition of the gold-bearing output. Automated corrections may improve consistency, but routine laboratory assays remain important because complexation can hide changes in available copper. Any control strategy should preserve the operating window established during testing.
The acidless approach can reduce dependence on corrosive acid leaching and support a smaller modular installation. It does not remove the need for chemical management, dust control, residual handling and safe storage. WEEE can contain brominated flame retardants, lead and other hazardous constituents, and a cleaner separation stage must still form part of a controlled waste-processing facility.
Australian urban mining and regulatory context
Australian feed logistics create a strong reason to manage copper close to the source. Sydney, Melbourne, Brisbane, Adelaide and Perth generate substantial electronic-waste streams, while dense collections make it possible to aggregate material before treatment. Yet copper is readily visible in building wiring, appliances, motor windings and cable offcuts. A mixed urban stream can therefore carry enough copper to influence ALS2 selectivity even when its gold concentration appears attractive.
Household habits add another variable. Australians regularly replace phones, tablets and laptops through retailer trade-in programmes, while councils in major cities collect televisions, computers and small electronics through dedicated services or waste facilities. Items placed in general waste can be wet, mixed with packaging and difficult to assay. Separating clean, traceable electronic equipment at collection would improve both feed quality and copper-concentration control.
Regulation remains a combination of Commonwealth policy and state or local requirements. The National Waste Policy and National Product Stewardship Framework support circular-economy development, while NSW’s E-waste and Recycling Program and council services in Melbourne illustrate the operational patchwork. Waste holders must follow the rules applying in their jurisdiction, and there is no single nationwide electronics take-back system that standardises every collection stream.
The Australian market also shapes commercial viability. Recovered gold is valued against AUD-denominated gold prices, while recyclers must balance metal value against collection, transport, assay and treatment costs. A compact ALS2 installation would need reliable local feed volumes and access to suitable analytical and residue-management services. Copper is valuable in its own right, so a plant that unnecessarily suppresses copper recovery may lose part of the commercial margin.
From copper control to commercial deployment
The project’s ALS2 feed comparison provides useful context by contrasting fire-assay feed with solution-based feed. Fire assay is a benchmark for gold contained in a bulk material, whereas solution-based feed exposes the separation chemistry to dissolved metals and suspended solids. Copper-control trials should preserve that distinction and measure the consequences for both recovery routes.
Horizon 2020 support has enabled research, technical development and pilot work around the ALS2Project concept. Commercial deployment still requires evidence from representative Australian WEEE, including seasonal feed changes, copper-rich electrical streams and realistic operating interruptions. A staged campaign should move from matched laboratory tests to continuous pilot operation, with agreed limits for gold recovery, copper carry-over, reagent use and final residue quality.
Contact the ALS2Project team with a representative WEEE sample and copper assay to scope a copper-controlled bench or pilot campaign. That step turns copper from an uncontrolled variable into a measured design input for selective gold recovery.