How ALS2 recovers rhodium from electrical relay contacts

Relay switches are often dismissed as tiny pieces of electronic waste, yet their contact surfaces can contain some of the rarest and most valuable platinum-group metals. Rhodium is prized for low contact resistance, corrosion resistance and stability under switching loads. When a relay fails or enters an equipment refurbishment stream, that coating can be discarded with the housing even though its material value remains. Turning these contacts into a recoverable resource starts with recognising them as a concentrated source of rhodium rather than mixed electronic scrap.

For Australian waste contractors, that distinction matters. Collection depots in Sydney, Melbourne and Brisbane receive household electronics and workshop equipment through council events, retailer take-back schemes and commercial disposals. Old control panels, automotive relays and industrial switchgear can arrive apart from phones or laptops, while service shops remove usable relays for reuse. These fragmented habits create both a supply opportunity and a sorting problem: rhodium-bearing contacts are diluted when they remain attached to bulky casings, springs, plastics and lower-value base metals.

ALS2Project is Ikoi S.p.A.’s initiative, backed by the European Union’s Horizon 2020 research and innovation programme, for recovering precious metals from electronic waste and waste electrical and electronic equipment recycling streams. Its central proposition is a separation route that avoids mineral-acid refining while fitting into compact recovery plants. For relay switches, the value lies in combining component-level collection with a process capable of handling small, heterogeneous quantities of coated contacts without routing every gram through a large conventional refinery.

This focused flow follows the material from collection through liberation, concentration, acidless separation and verified output. It also considers how Australian waste classification, transport distances and commercial feed volumes affect deployment. ALS2 should be assessed as a targeted circular-economy process for a real stream, not as a universal claim that every relay contains rhodium or that every waste fraction has equal value.

Why relay contacts need a dedicated stream

Electrical contacts are engineered as small, layered assemblies. A conductive base may be copper, nickel or silver alloy, while precious-metal plating can add gold, palladium or rhodium. The rhodium layer may be only a few micrometres thick, and its distribution can vary between relay models and manufacturers. A relay from an automotive control module is not chemically equivalent to an industrial high-voltage contact, so component labels alone can lead to the wrong separation assumptions.

Rhodium is often a surface finish, which means its richest metal is concentrated on the contact faces. If a switch is shredded with its plastic housing, the useful fraction becomes widely dispersed and may report poor grades to a sampler or refinery. Separating relays before crushing can preserve that information and create a manageable stream of bare contacts, bimetal washers and contact rivets. It also limits the polymer, solder and steel sent into the ALS2 separation stage.

That segregation supports both metallurgy and logistics. A dedicated stream can be sorted by relay type, cleaned without excessive media consumption and handed to a compact installation at a metropolitan depot or regional aggregation hub. Non-contact components can return to established WEEE material recovery routes instead of being processed alongside rhodium-bearing surfaces.

From relay switches to a rhodium-bearing product

The ALS2 route begins before the metal reaches the separation unit. Switches are inspected, de-mounted where practical and dismantled into casing, spring, armature and contact elements. Contact parts are separated from lower-value hardware, while contamination from potting compounds, solder and insulating resins is reduced. The aim is a clean feed in which precious-metal-bearing surfaces are present at a workable ratio to gangue and base metals.

The project’s acidless separation stage then addresses the mixed contact fraction without relying on the aggressive mineral-acid dissolution commonly used for platinum-group-metal concentrates. The technical benefit is not that chemistry disappears, but that the separation train uses a different chemical environment with fewer corrosive acid-handling requirements. Once valuable and unwanted constituents are separated, the rhodium fraction can proceed to appropriate finishing and assay steps rather than remaining in an undifferentiated residue.

Output must still be verified against agreed product criteria. Assay results should distinguish metallic rhodium in the recovered fraction from merely detectable rhodium in residue, while mass balances account for off-spec material, recycled feed and final samples. That discipline is essential in Australia, where a small difference between forecast and recovered grade can erase the margin on a high-value material. ALS2 provides upstream separation and enrichment; final metal quality depends on the finishing route and measured composition.

Consideration Acid-based refining Smelting route ALS2 approach
Core chemistry Strong-acid dissolution, often aqua regia for platinum-group-metal concentrates High-temperature alloying followed by refining Acidless separation of selected metal-bearing fractions
Relay-contact fit Entire assemblies may be dissolved, bringing base metals into solution Bulk treatment can dilute a thin rhodium coating Component liberation concentrates contact faces before separation
Facility profile Acid tanks, corrosion control, neutralisation and liquid-waste systems Furnace, feed preparation and off-gas capture Compact modular equipment for targeted feed streams
Environmental profile Acid use, neutralised salts and contaminated water require careful management Slags, dust and off-gases depend on feed and controls Lower acid burden; residues still require characterisation and lawful management
Main control point Selectivity and effluent quality Energy use and gas treatment Feed consistency, separation performance and residue handling
Best fit Large, well-characterised concentrates High-volume streams with sufficient grade Distributed WEEE streams rich in relay contacts

Why the acidless route changes the operating model

Conventional hydrometallurgy can recover rhodium from suitable concentrates, but it often begins with aqua regia or other strong acids, followed by purification, neutralisation and salt-bearing effluent management. Those steps are chemically demanding and require corrosion-resistant infrastructure. ALS2 offers a different route for selected feed: component segregation and enrichment are paired with acidless separation, allowing a plant to focus on a narrow fraction instead of dissolving an entire mixed assembly.

The environmental case should be stated precisely. Acidless does not mean zero waste, zero energy use or impact-free operation. Consumables, filters, residues, water and transport still require measurement, and final metal finishing may involve additional controlled processes. Even so, reducing dependence on large acid inventories can lower corrosion risk, operator exposure, neutralisation demand and the volume of acid-derived liquid residues. These are meaningful design gains for compact urban facilities when claims are demonstrated with representative feed and audited mass balances.

Physical fit is another advantage. The ALS2Project vision is a compact, modular plant suited to precious-metals recovery from distributed WEEE streams, rather than a sprawling complex tied to one metropolitan refinery. A smaller unit near a sorting hub can shorten the route from relay collection to recovered product and reduce freight on low-value bulk material. It can also operate beside an existing e-waste line as a specialised side process, making gradual commissioning and feed learning more practical.

Building a bankable feed in Australia

Commercial viability begins with a local source map. Sydney and Melbourne have large populations of serviced offices, industrial estates and transport fleets that generate obsolete control equipment; Brisbane’s mining, manufacturing and port industries add inventories of relays and switchgear. Regional operators face long haulage distances, so transport economics can favour consolidating clean contacts at a regional hub before shipment. The design target should be kilograms of a characterised contact fraction per route, not an undifferentiated e-waste tonnage.

Regulation shapes how that hub must operate. State and territory laws differ, and in New South Wales the Environment Protection Act 1999 and associated waste regulations cover activities involving waste assessment, storage and transport. Licensed contractors, documented transfers and controlled residues matter throughout the chain. Australia’s National Waste Policy supports better recovery and producer responsibility, while the federal Critical Minerals Strategy creates a policy setting for recovering strategically important metals. These frameworks make verified chain-of-custody data more valuable, not less.

Feed value must then be matched to separation cost. Small Australian lots can sometimes be consolidated through shared purchasing; the commercial logic of group buying structures is a useful analogy, although it sits outside the ALS2 process itself. A service model could combine scheduled collection from repairers and refurbishers with payment based on assayed rhodium content, then return non-contact relay materials to normal recycling routes. Transparent pricing and frequent assay feedback would help producers see why a tiny component stream deserves separate handling.

Run a controlled relay-recovery pilot

A credible pilot starts with representative feed, not a headline recovery claim. Collect relays from several sources, record model, age and application, remove obvious non-contact parts and split the sample into clean-contact, mixed-contact and base-metal fractions. X-ray fluorescence screening can assist sorting, but laboratory assay is needed for thin or variable rhodium coatings. Blending and duplicate samples should reveal whether the lot has enough predictable value to justify a dedicated route.

The ALS2Project team and Ikoi can then define a test plan around those fractions. Useful measures include rhodium recovery to the saleable product, metal purity, reagent and water consumption, residue generation, plant footprint and operator-safety controls. A short initial campaign can also identify practical issues such as contact geometry, dust, adhesive residues and feed variability. That evidence allows a modular plant design to be scaled around real Australian material rather than an idealised concentrate.

Start with one documented relay-switch lot, agree on sampling and assay methods, and invite Ikoi S.p.A. to review a controlled ALS2 demonstration through the ALS2Project. Contact the project team with the feed profile, assay results and proposed residue-handling route; that gives the team the evidence needed to scope a modular Australian pilot around verified performance rather than assumptions.