ALS2 platinum recovery from exhaust gas sensors

Exhaust gas sensors are small components with outsized value. Fit for petrol engines, three-way catalytic sensors and diesel nitrogen oxide sensors use platinum-group metals to measure or control emissions accurately. When vehicles reach the end of their working life, these sensors enter a fragmented waste stream containing steel housings, ceramic substrates and valuable catalytic coatings.

The ceramic element inside each sensor is especially important. Its porous, honeycomb-like structure carries a washcoat containing very small quantities of platinum, palladium or rhodium. Although the precious-metal loading is low, the material has high economic value. Other constituents, including silica, alumina, ceria and zirconia, complicate direct reuse and make selective recovery technically demanding.

ALS2 for platinum recovery from exhaust gas sensor substrates is part of Ikoi S.p.A.’s wider work on safer separation technologies. The approach seeks to replace or reduce reliance on conventional acid-based refining while recovering valuable metals from electronic waste and WEEE streams. It is supported by the European Union’s Horizon 2020 research and innovation programme and is intended for compact precious-metals recovery plants.

For Australia, the opportunity combines an established automotive repair sector with growing interest in urban mining and circular materials. Sensors removed during servicing, accident repair and vehicle dismantling often pass through several businesses before reaching a refinery. A coordinated recovery pathway could capture this material, reduce losses and create a traceable domestic supply of platinum-group metals.

Why sensor substrates are a valuable feedstock

Sensor substrates offer a practical secondary source of platinum-group metals. Modern sensors can contain enough recoverable precious metal to justify dedicated collection, particularly when material from many vehicles is consolidated. The concentration may vary substantially between sensor models, so a representative assay is essential before assigning value or selecting a processing route.

The main challenge is separation. Platinum is dispersed through a coating and bonded to a porous ceramic body, while the surrounding sensor can also contain stainless steel, electrical contacts, lubricants and organic residues. Mechanical preparation can liberate the ceramic, but physical liberation alone does not create a marketable metal. The platinum-bearing fraction must be separated from the bulk substrate and then refined to the required purity.

This waste stream is also likely to grow as manufacturers improve fuel efficiency and emissions control. Although electrification reduces the need for exhaust sensors in new battery-electric vehicles, Australia’s existing vehicle fleet, second-hand vehicle trade and longer service lives of older cars will continue to supply sensors for years. Urban mining therefore offers a near-term feedstock alongside longer-term opportunities in industrial catalysts and electronic waste.

How acidless separation changes the recovery route

Conventional sensor recycling often involves shredding, followed by acid leaching and further refining to separate platinum-group metals from ceramic and metallic residues. Mineral acids can dissolve the target metals effectively, but they also create corrosive solutions, hazardous waste and exposure risks for workers. Energy, reagent recovery and effluent treatment add cost and environmental impact.

The ALS2 technology focuses on selective separation without relying on the same intensive acid-based attack. Its purpose is to separate and concentrate metal-bearing material while reducing acid demand and the management of hazardous liquids. For small regional facilities, that difference could make recovery more compact, safer and compatible with sites that cannot support a full traditional refinery.

An acidless process should not automatically be treated as impact-free. Water consumption, energy use, reagent manufacture, metal losses and the treatment of solid residues still need to be measured. Commercial assessments should use life-cycle data and verified test results rather than assumptions. Even so, reducing corrosive effluents may improve worker safety and simplify compliance with strict environmental controls.

From workshops to a concentrated metal stream

A workable Australian collection system would connect automotive workshops, accident-repair specialists, dealerships, recyclers and vehicle dismantlers. Melbourne, Sydney and Brisbane each have large service and used-vehicle markets that generate spent sensors. Small businesses may lack the equipment or metal value to process sensors individually, making aggregation through an authorised collector economically important.

Once collected, sensors require controlled dismantling. The steel body and electronic components can be separated from the ceramic element before size reduction. This protects workers, reduces contamination and improves the consistency of the feed sent to ALS2 processing. Sensors should remain identified by source and vehicle or repair batch wherever possible, supporting both traceability and material-quality records.

After separation, the platinum-bearing concentrate requires assay and an established refining route. The recovered material may not meet bullion or jewellery specifications immediately, nor should it be treated as commercially equivalent to newly mined platinum. Its value depends on metal content, recovery yield, impurity profile, processing cost and the buyer’s quality requirements. Testing before shipment prevents low-grade material from being misrepresented as refined metal.

Australian regulation, customs and logistics

Environmental regulation in Australia is divided among federal, state and territory authorities. The National Waste Policy supports better recovery of materials from waste streams, yet there is no single national electronic-waste law covering every recovery activity. In New South Wales, Victoria and Queensland, waste transport and processing may require licences or approved facilities depending on the classification and quantity of material.

These rules make responsible partnerships particularly valuable. A network operator should confirm whether collected sensors qualify as waste, which transport documentation apply and where final treatment is permitted. Residues containing platinum must not be moved or disposed of merely because their hazardous characteristics are unfamiliar to the handler. Local environmental regulators should be consulted before the recovery chain is established.

Cross-border movement introduces another layer. Equipment, catalyst samples and concentrated residues may attract environmental, customs and import controls. Importers should use the correct tariff classification and an accredited customs broker, while accounting for GST, freight, permits and record-keeping requirements. Waste exports also require scrutiny under Australian controls, so any international shipment should begin with a permit check rather than after commercial terms have been agreed.

A local-first model may offer the simplest commercial path. Feedstock can be consolidated within each state, processed near an established precious-metals hub and then transferred to a qualified refiner. This reduces border complications while preserving the chain of custody needed by responsible buyers.

Commercial pathways for recovered platinum

Recovered platinum-group metals could enter several established markets. Refiners may value sensor-derived feed for platinum, palladium or rhodium recovery, while laboratories, chemical manufacturers and catalyst producers offer additional outlets. Refiners and jewellery businesses in Perth, Melbourne and Sydney already operate within Australian precious-metals value chains, creating channels for responsibly verified material.

Market value depends on more than the spot price. Buyers increasingly examine provenance, responsible sourcing, recovery efficiency and environmental performance. A documented process that begins with Australian automotive waste can distinguish the material from mixed or untraceable feed. Digital batch records, chain-of-custody documentation and independent assay results can support stronger commercial claims.

ALS2’s compact-plant concept could suit regional aggregation hubs where a large refinery would be uneconomic. A facility might process sensors from several workshops, deliver a small but consistent precious-metal concentrate and send residue for appropriate treatment. Local recovery also reduces freight, handling losses and exposure to commodity-price movements associated with shipping loose low-value material across long distances.

Before adoption, operators need dependable data on feed composition and plant yield. Waste-stream sampling must reflect the vehicles and sensor types common in the intended catchment. Contracts should allocate responsibility for contamination, assay variation, residue disposal and price adjustments, providing all parties with a clear basis for valuing the recovered output.

Build a circular platinum supply chain

ALS2 offers a promising bridge between difficult-to-process automotive waste and concentrated precious-metal streams. Its acidless separation approach can improve safety and reduce the burden of corrosive refining, while modular equipment may bring recovery closer to workshops and dismantlers. The technology’s commercial strength will depend on verified environmental performance and reliable throughput in real Australian feedstock.

A successful Australian project would require several elements working together: authorised collection, controlled sensor dismantling, accurate assaying, suitable separation capacity, residue management and a responsible refining partner. Municipalities, regulators and industry associations can help establish consistent standards, while automotive businesses provide the feedstock needed to improve material consistency.

The Horizon 2020 backing and international research connections create a foundation for pilot work and commercial collaboration. Australian technology developers, recyclers, refiners and research organisations can contribute local waste data, industrial expertise and market access. This cooperation can test ALS2 under Australian regulations and help translate European research into an operational recovery model.

Businesses and research teams interested in contributing feedstock, hosting a demonstration plant or developing a refining partnership should use the ALS2Project contact details to discuss technical requirements, sample data and collaboration opportunities with Ikoi S.p.A.